{
    "type": "filament",
    "filament_id": "01001",
    "setting_id": "GFSA04_CREALITY_00",
    "name": "Creality Hyper PLA @Ender-5Max-all",
    "from": "system",
    "instantiation": "true",
    "inherits": "fdm_filament_common",
    "activate_air_filtration": "0",
    "activate_chamber_temp_control": "0",
    "additional_cooling_fan_speed": "0",
    "chamber_temperature": "0",
    "close_fan_the_first_x_layers": "1",
    "compatible_printers": [
        "Creality Ender-5 Max 0.4 nozzle"
    ],
    "complete_print_exhaust_fan_speed": "80",
    "cool_plate_temp": "45",
    "cool_plate_temp_initial_layer": "45",
    "cool_special_cds_fan_speed": "0",
    "default_filament_colour": "\"\"",
    "during_print_exhaust_fan_speed": "60",
    "enable_overhang_bridge_fan": "1",
    "enable_pressure_advance": "1",
    "eng_plate_temp": "50",
    "eng_plate_temp_initial_layer": "50",
    "fan_cooling_layer_time": "100",
    "fan_max_speed": "100",
    "fan_min_speed": "100",
    "filament_cooling_final_speed": "3.4",
    "filament_cooling_initial_speed": "2.2",
    "filament_cooling_moves": "4",
    "filament_cost": "30",
    "filament_density": "1.24",
    "filament_deretraction_speed": "nil",
    "filament_diameter": "1.75",
    "filament_end_gcode": [
        "; filament end gcode \n"
    ],
    "filament_flow_ratio": "0.97",
    "filament_is_support": "0",
    "filament_load_time": "0",
    "filament_loading_speed": "28",
    "filament_loading_speed_start": "3",
    "filament_max_volumetric_speed": "50",
    "filament_minimal_purge_on_wipe_tower": "15",
    "filament_multitool_ramming": "0",
    "filament_multitool_ramming_flow": "10",
    "filament_multitool_ramming_volume": "10",
    "filament_notes": "\"\"",
    "filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
    "filament_retract_before_wipe": "nil",
    "filament_retract_lift_above": "0",
    "filament_retract_lift_below": "0",
    "filament_retract_lift_enforce": "All Surfaces",
    "filament_retract_restart_extra": "nil",
    "filament_retract_when_changing_layer": "nil",
    "filament_retraction_length": "nil",
    "filament_retraction_minimum_travel": "nil",
    "filament_retraction_speed": "nil",
    "filament_shrink": "100%",
    "filament_shrinkage_compensation_z": "100%",
    "filament_soluble": "0",
    "filament_start_gcode": [
        "; filament start gcode\n"
    ],
    "filament_toolchange_delay": "0",
    "filament_type": [
        "PLA"
    ],
    "filament_unload_time": "0",
    "filament_unloading_speed": "90",
    "filament_unloading_speed_start": "100",
    "filament_vendor": [
        "Creality"
    ],
    "filament_wipe": "nil",
    "filament_wipe_distance": "nil",
    "filament_z_hop": "nil",
    "filament_z_hop_types": "nil",
    "full_fan_speed_layer": "0",
    "hot_plate_temp": "45",
    "hot_plate_temp_initial_layer": "45",
    "nozzle_temperature": "220",
    "nozzle_temperature_initial_layer": "220",
    "nozzle_temperature_range_high": "240",
    "nozzle_temperature_range_low": "190",
    "overhang_fan_speed": "100",
    "overhang_fan_threshold": "50%",
    "pressure_advance": "0.04",
    "reduce_fan_stop_start_freq": "1",
    "required_nozzle_HRC": "0",
    "slow_down_for_layer_cooling": "1",
    "slow_down_layer_time": "5",
    "slow_down_min_speed": "20",
    "support_material_interface_fan_speed": "-1",
    "temperature_vitrification": "60",
    "textured_plate_temp": "45",
    "textured_plate_temp_initial_layer": "45"
}